ISO-20653-2006 Ipx5/Ipx6 Dust Blowing Test Chamber

• After-sales Service: Available
• Power Supply: AC380V
• Certification: CE, ISO
• Warranty: 1 Year
• Frequency: 50Hz
• Power: 16kw
• Model NO.: HCTE0034
• Sample Frame Load: 30kg
• Air Blower: Full-Plastic Centrifugal Fan
• Anemometer: Handheld Adjustable
• Transport Package: Plywood
• Specification: 1000*1000*1000mm
• Trademark: H&H
• Origin: China
• Production Capacity: 10 Sets Per Month

Product Description

 ISO-20653-2006 And GBT-2423.37 Dust Blowing Test Chamber

 

This equipment is suitable for the test of electrical electronics, automobiles, motorcycle parts, and seals to prevent sand dust from entering the seals and shells in large dust environments.To test the use, storage and transportation performance of electronic and electrical products, automobiles, motorcycle parts, and seals in the sand and dust environment.The purpose of the test was to determine the possible harmful effects of the particles carried by the air flow on the electrical products.


Test Purpose:
The test can be used to simulate open sand and dust air ambient conditions induced by natural or artificial disturbances such as vehicle motion.
 
Meet The Standards:
GB/T2423.37-2006 Lc1 or Lc2 test,IEC60068-2-68 Lc1 or Lc2 test Dust blowing test for ISO 20653:2006, procedure I procedure test for GJB150.12A-2009, procedure I procedure test for MIL-STD-810H 510.7
 
Design Principle:
Design a conical funnel, the bottom of the dust collector, at the dust extraction mouth (right) install high pressure turbine circulation fan inlet, the dust to the inner box at the bottom of the box through the bottom to the left up, before the disposal box, blow into the dust dust from the left to the test box, dust horizontal dust to the right, so as to start to cycle.
 
Control Box and Test Box Are of the Overall Type:
The bottom of the room body is funnel-shaped, and the dust shaking motor at the bottom will assist in dust recovery
The test box is approximately a cube, whose edge length in the airflow cross section is at least 3 times the maximum of the vertical or horizontal side length of the vertical air flow direction. The test box has the heating function;
The test box has a pretreatment box, and the two boxes have the same air flow section. The air diversion sheet is placed at the back of the entrance of the air flow channel leading to the front box, produce horizontal laminar air flow through the overall arrangement, arrange the blower device producing air flow after the test box, and draw air from the test box and send it to the front treatment box through the air flow channel;
The dust device is of external type and connected by air duct.
 
Main Technical Indicators:

Model	HCTE0034-600	HCTE0034-800	HCTE0034-1000
Inner box size W * D * H(No air duct)	600×600×600mm	800×800×800mm	1000×1000×1000mm
Outer box size W * D * H	3500×1400×1700mm	4000×1700×1900mm	5000×2000×2000mm
Standard	ISO-20653-2006,GBT-2423.37
Fine dust	75um below
Thick dust	150um below
Sand	150um-890um
Airflow rate	6m/s, 8.9m/s, (18m/s, 29m/s) blow the sand
Dust concentration in the box and pipe	5G/m³,10.6G/m ± 7 (Touch-screen-adjustable)
Arizona dust dosage	2-3kg / m (random mismatch customers need their own)
Metal screen size	Nominal line diameter 50um and nominal spacing between lines 75um or below 150um
Air blower	Full-plastic centrifugal fan
Sample frame load	30kg
Basic structure of dust blowing	Composition of pretreatment box, test box, vacuum suction, dust collection box, circulating vacuum blowing device, vacuum system, dust storage tank, flow valve, heating system, reflux blade, sample turntable, protection network, concentration meter dust return pipe, etc.
Dust blowing sand structure	Laminar flow, from left to right, blowing sand is from right to left
Vacuum system	Pressure regulating valve, suction nozzle, pressure regulating three-piece set
Vacuum pump range	60~600L/H
Controller control function	Dust blowing time (stop, blow) h / m/s is adjustable
	Cycle cycle: any adjustable
	Power: direct blow
	Preset test time: 0s~999h99m99s is adjustable
Control system	PLC and Touch Screen Smart Control System
Sensor	The PT100 test sensor
Anemometer	Handheld adjustable
lysimeter	The simulated quantity control signal was transmitted to the PLC module for precise control
Internal box material	SUS 304 mirror-faced stainless steel
Outbox material	SUS 304 stainless steel
On the door	Large observation window, special air duct design, to ensure that the box produces a concentration of laminar air flow
heating system	Stainless steel mica sheet heating cover
Equipment use conditions	Power supply: AC380 V; frequency: 50HZ; power: 16KW
Ambient condition	Temperature 5ºC to 40ºC relative temperature 85%RH
Safety protection system	Line order protection, electric leakage protection, super-temperature protection, abnormal protection